Button 3: single colours (white, red, green, blue, total of 7 static colours)
Button 4: colour fades (over 5 modes)
Button 5: speed control Button 6: brightness (dimming)
***RELIABLE REMOTE CONTROL OPERATION***
Modified receiver than can reach up to 15 meters without extending antenna and more than 30 meters (with antenna extended)!
Our modified Tx/Rx can 100% perform the following functions:
Precise and long range on/off
Precise and long range brightness control (led dimmer)
Precise and long range single colours mode control
Precise and long range RGB mode control
Precise and long range pause function
Precise and long range speed control for the RGB mode.
Important note:
Customers that purchased (from this website) older versions of the specific model can get our new upgraded version at no extra charge and free shipping!
Using the appropriate led controller it is possible to adjust the brightness of the led without any flickering effect. Not all led controllers are capable for led dimming; proper dimming for led lighting (avoiding led colour shift) can only be done by pulse width modulation based controllers.
LT-SYSTEM-3600RC is a full colour multifunctional rgb led controller based on PWM technology and designed to control colour changing combinations of LED strip lighting with 4-pin 3-loop cables (common anode). It can be adjusted through manual buttons or matching remote control device. Also this unit can run as a standalone controller or linked with an rgb amplifier which can unlimitedly expand its capabilities.
Specification:
INPUT VOLTAGE: 5 to 12V DC
MAXIMUM LOAD CURRENT: 6A / Channel (3 channels R, G, B)
OUTPUT POWER: 1 TO 90W (5V), 1 TO 220W (12v), 1 TO 450W (24V)
SCENE MODES: 10 RGB modes + static 7 colours mode
GRAY SCALE: 256 LEVELS (RGB)
BRIGHTNESS ADJUST: 0 TO 32 LEVELS
SPEED ADJUSTMENTS: 16 LEVELS
PROTECTION: OVERLOAD (AUTO)
OTHER FUNCTIONS: RESTORE OF SETTINGS AFTER POWER OFF/ON/PAUSE
SCENE STATUS: LED INDICATORS SHOWING THE CONTROLLERS OUTPUT STATUS
REMOTECONTROLRANGE: 20 to 100 meters
DIMENSIONS: L211 X W40 X H30 (mm)
PACKAGE DIMENSIONS: L220 X W43 X H33 (mm)
WEIGHT: 200g
To run 10 meters of RGB strip you will need a 5A switching mode power supply, an RGB controller of your choice and the flexible strip. Basic soldering skills to do some simple connections may be necessary!
To control more than 10 meters of RGB strip using just one remote control, for every extra 10 meters a 5A power supply and an RGB led amplifier is necessary (LT-System-3060 or HL-AH3H10).
HL-AH3H10 (RGB led amplifier) is a low version of an RGB amplifier but in order to get synchronized with the wireless RGB controller (or additional rgb amplifiers) will need an extra cable connecting negative of all power supplies used!
Using LT-SYSTEM-3060 rgb led amplifier, does not require any extra connections.
Warning! Large file size. Depending on your connection, the page may be slow to open. Alternatively you can right click here and choose "Save Target As".
***Newly added functions and modifications are not yet included in this manual***
I have purchased this controller together with my LED strip. The product is well built with good quality plastics. The controls are logically organized and easy to use. The remote controller is nice, small and handy when you are just sitting in your sofa, watching TV and don't feel like getting up. The controller offers a variety of modes I have not been able to fully explore yet, but I am sure everyone is going to find the ones that suits him/her. Installation of this unit cannot be easier. Just plug the wires and play. Hi-line customer support was very friendly and professional. I have exchanged at least 10-15 emails with Polis from Hi-line. He has answered every single one of them within 24 hours. Thank you and I will buy from Hi-line again as soon as I figure out where to put more LEDs in my house. :)
